An automotive solenoid injector operates within common rail systems of engine. They are the most frequently used supply systems of high pressure fuel to the engines. A solenoid injector enables the separation of high pressure generation function and fuel injection performance. Consequently, it provides flexibility and adaptation of the injection system to the engine, which have higher efficiency than conventional systems. Since fuel is located in the chamber with constant high pressure, it is possible to model the injection freely by means of sending electrical impulses to the injectors. A programmer and electronic control unit, supplies power to the solenoid valve of the injector, which activates the sprayer. The injection of fuel is complete after the power supply to the solenoid valve is discontinued. The amount of fuel to be injected is decided by the solenoid valve is open. It is not dependent on engine rotational speed or an injection pump.

The common rail direct injection system, in an automotive, offers additional ways of influencing the combustion process. The most important reason for this is a completely independent control over the air flow and fuel metering processes. At the same time, the high injection pressure of up to 20 MPa improves the atomization and thus, the preparation of a homogeneous mixture. By directly injecting fuel into the combustion chamber result in formation of fuel manifold-wall film, which often leads to problems in gasoline engines during transient operating conditions, is avoided. The common rail direct injection methods are preferred by automotive engine manufacturers due to the advantages mentioned above. Solenoid injectors fulfill the demand for high pressure, as they have a more sustainable internal body than that of other type of injectors. Moreover, their manufacturing cost is relatively low. The ability to maintain high pressure in the common supply line, irrespective of engine speed, is a key factor that drivers the automotive solenoid injector market. Consistent increase in demand for high efficiency engines has presented numerous opportunities for the automotive solenoid injector market.

Solenoid injectors have the ability to produce a maximum five pulses per cycle, and it is difficult to control the delivery of fuel in solenoid injectors. These factors act as key restraints for the automotive solenoid injector market.

The automotive solenoid Injector market can be segmented based on injection system, type of solenoid used, technology, and geography. In terms of injection system, the automotive solenoid injection system market can be segmented into Multi Point Fuel Injection (MPFI) system and Common Rail Direct Injection (CRDI) system. In the CRDI system, the fuel is injected directly above the piston, whereas in the MPFI system the fuel is injected in the intake manifold. Based on type of solenoid used, the automotive solenoid injector market can be segregated into AC laminated solenoid, DC C-frame solenoid, DC D-frame solenoid, linear solenoid, and rotary solenoid. AC laminated solenoid is famous for attracting force that can be applied by it in their first stroke. DC C & D-frame solenoids are named so due to the shape of covering around the coil. Linear solenoid is capable of applying a pull or push force. Based on technology, the automotive solenoid injector market can be segmented into first generation solenoid injectors and second generation solenoid injectors. Second generation solenoid injectors are able to supply fuel at a high pressure, up to 2500 bar, and can provide eight individual injections per cycle. While the first generation of automotive solenoid injectors can provide up to five individual injections per cycle.

Based on geography, the automotive solenoid Injector market can be segmented into North America, Asia Pacific, Europe, Middle East & Africa, and Rest of the World. Asia Pacific is a prominent market for automotive solenoid injectors. Increasing demand for automotive is fuelling the demand for automotive solenoid injectors.

Automotive components such as fuel injectors play a vital role in order to meet the increased demand for high efficiency automotive engines. Prominent manufacturers of solenoid injectors has great focusing on innovation for increasing the efficiency of solenoid injectors. Key players operating in the automotive solenoid injector market are Robert Bosch GmbH, Continental AG, DENSO CORPORATION, Delphi Automotive LLP, Woodward, Inc, Sentec, and Eaton.

The report offers a comprehensive evaluation of the market. It does so via in-depth qualitative insights, historical data, and verifiable projections about market size. The projections featured in the report have been derived using proven research methodologies and assumptions. By doing so, the research report serves as a repository of analysis and information for every facet of the market, including but not limited to: Regional markets, technology, types, and applications.

The study is a source of reliable data on:

  • Market segments and sub-segments
  • Market trends and dynamics
  • Supply and demand
  • Market size
  • Current trends/opportunities/challenges
  • Competitive landscape
  • Technological breakthroughs
  • Value chain and stakeholder analysis

The regional analysis covers:

  • North America (U.S. and Canada)
  • Latin America (Mexico, Brazil, Peru, Chile, and others)
  • Western Europe (Germany, U.K., France, Spain, Italy, Nordic countries, Belgium, Netherlands, and Luxembourg)
  • Eastern Europe (Poland and Russia)
  • Asia Pacific (China, India, Japan, ASEAN, Australia, and New Zealand)
  • Middle East and Africa (GCC, Southern Africa, and North Africa)

The report has been compiled through extensive primary research (through interviews, surveys, and observations of seasoned analysts) and secondary research (which entails reputable paid sources, trade journals, and industry body databases). The report also features a complete qualitative and quantitative assessment by analyzing data gathered from industry analysts and market participants across key points in the industry’s value chain.

A separate analysis of prevailing trends in the parent market, macro- and micro-economic indicators, and regulations and mandates is included under the purview of the study. By doing so, the report projects the attractiveness of each major segment over the forecast period.

Highlights of the report:

  • A complete backdrop analysis, which includes an assessment of the parent market
  • Important changes in market dynamics
  • Market segmentation up to the second or third level
  • Historical, current, and projected size of the market from the standpoint of both value and volume
  • Reporting and evaluation of recent industry developments
  • Market shares and strategies of key players
  • Emerging niche segments and regional markets
  • An objective assessment of the trajectory of the market
  • Recommendations to companies for strengthening their foothold in the market   

Note: Although care has been taken to maintain the highest levels of accuracy in TMR’s reports, recent market/vendor-specific changes may take time to reflect in the analysis.

This study by TMR is all-encompassing framework of the dynamics of the market. It mainly comprises critical assessment of consumers' or customers' journeys, current and emerging avenues, and strategic framework to enable CXOs take effective decisions.

Our key underpinning is the 4-Quadrant Framework EIRS that offers detailed visualization of four elements:

  • Customer Experience Maps
  • Insights and Tools based on data-driven research
  • Actionable Results to meet all the business priorities
  • Strategic Frameworks to boost the growth journey

The study strives to evaluate the current and future growth prospects, untapped avenues, factors shaping their revenue potential, and demand and consumption patterns in the global market by breaking it into region-wise assessment.

The following regional segments are covered comprehensively:

  • North America
  • Asia Pacific
  • Europe
  • Latin America
  • The Middle East and Africa

The EIRS quadrant framework in the report sums up our wide spectrum of data-driven research and advisory for CXOs to help them make better decisions for their businesses and stay as leaders.

Below is a snapshot of these quadrants.

1. Customer Experience Map

The study offers an in-depth assessment of various customers’ journeys pertinent to the market and its segments. It offers various customer impressions about the products and service use. The analysis takes a closer look at their pain points and fears across various customer touchpoints. The consultation and business intelligence solutions will help interested stakeholders, including CXOs, define customer experience maps tailored to their needs. This will help them aim at boosting customer engagement with their brands.

2. Insights and Tools

The various insights in the study are based on elaborate cycles of primary and secondary research the analysts engage with during the course of research. The analysts and expert advisors at TMR adopt industry-wide, quantitative customer insights tools and market projection methodologies to arrive at results, which makes them reliable. The study not just offers estimations and projections, but also an uncluttered evaluation of these figures on the market dynamics. These insights merge data-driven research framework with qualitative consultations for business owners, CXOs, policy makers, and investors. The insights will also help their customers overcome their fears.

3. Actionable Results

The findings presented in this study by TMR are an indispensable guide for meeting all business priorities, including mission-critical ones. The results when implemented have shown tangible benefits to business stakeholders and industry entities to boost their performance. The results are tailored to fit the individual strategic framework. The study also illustrates some of the recent case studies on solving various problems by companies they faced in their consolidation journey.

4. Strategic Frameworks

The study equips businesses and anyone interested in the market to frame broad strategic frameworks. This has become more important than ever, given the current uncertainty due to COVID-19. The study deliberates on consultations to overcome various such past disruptions and foresees new ones to boost the preparedness. The frameworks help businesses plan their strategic alignments for recovery from such disruptive trends. Further, analysts at TMR helps you break down the complex scenario and bring resiliency in uncertain times.

The report sheds light on various aspects and answers pertinent questions on the market. Some of the important ones are:

1. What can be the best investment choices for venturing into new product and service lines?

2. What value propositions should businesses aim at while making new research and development funding?

3. Which regulations will be most helpful for stakeholders to boost their supply chain network?

4. Which regions might see the demand maturing in certain segments in near future?

5. What are the some of the best cost optimization strategies with vendors that some well-entrenched players have gained success with?

6. Which are the key perspectives that the C-suite are leveraging to move businesses to new growth trajectory?

7. Which government regulations might challenge the status of key regional markets?

8. How will the emerging political and economic scenario affect opportunities in key growth areas?

9. What are some of the value-grab opportunities in various segments?

10. What will be the barrier to entry for new players in the market?

Note: Although care has been taken to maintain the highest levels of accuracy in TMR’s reports, recent market/vendor-specific changes may take time to reflect in the analysis.

Custom Market Research Services

TMR offers custom market research services that help clients to get information on their business scenario required where syndicated solutions are not enough.

REQUEST CUSTOMIZATION

Automotive Solenoid Injector Market

Pre Book